Water Heater Replacement – How to Keep Your Water Heater Running Efficiently

You’ll likely need to hire a professional for this project. A water heater installation typically costs $906 to $3,910.

Water Heater

Having adequate hot water is vital for daily hygiene and household chores. A leaking water heater is a huge problem that can soak belongings and lead to a flooded basement. Contact Water Heater Replacement Denver for professional expertise.

A faulty tank can make popping, banging, or rumbling noises. These are signs that it’s time to replace the unit.

A new water heater can cost up to $1,600. The price depends on the type of device and whether you opt for a tank-based or tankless system, as well as its fuel source. A tankless system requires more extensive plumbing, but it will save you money on energy bills over time.

The first step in determining whether to repair or replace your water heater is to understand the signs that it may be nearing the end of its life. If you have a gas unit, check that the pilot light is still lit and that the gas line is working properly. You should also inspect the tank for leaks and rusting.

If you notice that your hot water isn’t as hot as it used to be, this could be a sign that the heating element has broken. This is a common problem that is easily fixed by a professional. However, replacing the entire heating system is typically more expensive.

It is important to consider the location where you want to install your new water heater. If you choose to move it from its previous location, you will need to reroute your plumbing and potentially ventilation systems, which will increase the installation costs.

Another thing to keep in mind is the price of additional features that are offered by some manufacturers. These include energy-saving technology and smart controls. However, the higher cost often reflects the superior performance and longevity of these models.

One of the best ways to reduce your replacement cost is to shop around and compare prices. It is also wise to choose a model with a longer warranty. The average water heater warranty is three to 12 years, so choosing a longer warranty will likely save you money in the long run.

Finally, don’t forget to factor in the removal and disposal of your old water heater. This is usually included in the initial estimate, but if it isn’t, you will need to pay for junk pickup or take care of it yourself. A plumbing company will often help with this, but they might charge a fee for this service.

Energy Efficiency

The best water heaters are efficient, saving you money on your energy bills. Choosing an energy-efficient model will also help reduce environmental pollution by dumping fewer pollutants into the atmosphere. If your existing water heater is nearing or has passed its life expectancy, consider replacing it with a more efficient model. You may find that your energy savings will pay for the new unit in a few years.

When selecting a new water heater, think about how much hot water you use in a day, what time of the day you use the most hot water, and how many people live in your home. This will help you determine the size of tank or tankless water heater that you need. You should also choose a type of water heater, including gas, electric, or hybrid.

Some models have extra features that can increase efficiency or reduce energy costs, but these features will add to the overall cost of the unit. You should consult with a plumber to learn more about the different types of water heaters and what options are available to you.

Water heating can account for up to a fifth of your total utility bill, so it’s important to choose an efficient model. The EPA’s Energy Star program helps consumers identify appliances that meet specific energy efficiency guidelines. You can also save money by installing an energy-efficient electric heat pump or condensing gas water heater, which will lower your monthly and yearly energy costs.

If you want to save even more on your utility bills, try insulating your water heater and pipes. This will prevent heat loss, cutting your energy costs by up to 10 percent. Additionally, you can save money by lowering your water heater temperature to 140 degrees Fahrenheit. By doing so, you can cut your water heating costs by 3 to 5 percent each year.


If your water heater is in the middle of a major leak and causing expensive damages, it may be time to call a professional. These experts can help you repair the damage and install a new water heater before it’s too late. They can also recommend the best water heater replacement model for your home.

Before you begin, it’s a good idea to consult your local plumbing codes to see what regulations apply in your area. Some jurisdictions require that you get a permit for this project, and others have specific requirements for materials and installation procedures. Also, make sure that your utility company has turned off the gas to your old water heater and that it is completely disconnected from your house’s pipes.

You’ll need to drain the tank, cut the water line, and disconnect the gas line and pressure relief valve. Then, you can remove the unit from its location. You’ll need to use an appliance dolly and have a friend to help you lift the heavy water heater. The next step is to clean the floor where you plan to place your new water heater. Then, install the new one in its location. It’s important to make sure that it is at least 6 inches away from any walls or furniture. It’s also important to ensure that it is level.

Connect the new pipes to the cold water inlet and hot water outlet. You can solder the connections or use sharkbite fittings. Soldering copper is one of the easiest building skills to master, and it’s much safer than using PVC. It’s also a good idea to use dielectric unions, which protect the pipes from corrosion and allow them to be removed without cutting or soldering in the future.

You should also reinstall the temperature and pressure relief valve and discharge drainpipe. Finally, you should turn on the power and water to your new water heater and test it for leaks. If your water heater isn’t producing enough hot water or if you’re experiencing temperature fluctuations, it might be time to contact a pro.


Taking proper care of your water heater can keep it running efficiently for longer. A good way to do this is by regularly checking the condition of your unit and having it inspected by a professional for any minor problems that can be corrected quickly before they turn into major ones. Keeping an eye on these issues can also prevent your water heater from breaking down early and save you from costly repairs in the future.


If you notice water leaking from the water heater, this is a sign that it’s time for a replacement. Water leaks are often caused by corrosion, which can cause damage to the interior of the tank and other parts of the house. If left untreated, water leaks can soak and ruin belongings and lead to mold growth.

Low hot water supply

A common problem that can indicate a failing water heater is when the water is always running cold or there’s not enough hot water for your household needs. This could be due to a broken heating element, sediment buildup, or an insufficient size tank.

High energy bills

A water heater that’s older will use more energy to function, which can lead to an increase in your utility bill. A newer water heater will use less energy and help reduce your electricity costs.


Foul or metallic odors in your hot water may be caused by rust and corrosion inside the tank. In some cases, this issue can be solved with a tank flush, but if the damage is irreparable, a new water heater may be necessary.

Rumbling noises

A noisy water heater is another common sign that it’s time to replace it. Minerals and sediment build up in the tank, creating air pockets that cause them to rattle when the unit operates. This can wear down the device and shorten its lifespan, so it’s important to schedule a repair as soon as possible.

The first step in installing a new water heater is to drain the old one by attaching a garden hose to the valve at the bottom of the tank and placing the other end of the hose over a floor drain or outside. Next, shut off the gas and electric power to the water heater and disconnect the hose from the cold and hot water lines using a pipe wrench or channel-lock pliers for compression fittings and a pipe cutter for soldered connections.